移印耐酒精电镀油墨 

壹﹑油墨性能： 亮光、柔韌好、抗刮耐磨、耐酒精、耐溶劑、附著力好。
  二﹑適用範圍： 金屬、玻璃、陶瓷、處理過及未處理的pp、pe、電鍍面、uv面等材料。
  三﹑物理特性： 1.印刷方式：絲印、移印。
  2.過網性：80t-140t。
  3.表幹時間：常溫下自然幹燥20分鐘以上；
    實幹時間：常溫下自然幹燥24小時以上。
    烘 烤：金屬、玻璃、陶瓷烘烤溫度150℃保溫30分鐘；
           pp、pe電鍍面等材料烘烤溫度80℃保溫30分鐘。
  4.稀釋劑：407金屬開油水、783慢幹水。
  5.塗覆面積：35㎡/kg（120t網版）。
  6.產品細度：5μ以下。
  7.清洗劑：洗網水、環已酮。
  8.刮刀：65-85度聚胺脂刮刀。
  四﹑化學性能： 只可與本系列油墨相互調配。
  五﹑使用方法： 1.使用前把油墨充分攪拌均勻，用後隨時封閉；
  2.倒出部份油墨，以油墨：固化劑8：1的比例混合充分攪拌，再加入10-30%的稀釋劑攪拌均勻後印刷。
  3.承印物表面須幹凈，無油汙﹑灰塵等；
  4.多色套印時需待墨層表面幹後才可進行下壹顏色的印刷；
  5.連續印刷，間斷印刷後應用洗網水清洗網版；
  6.網版堵塞，可用洗網水、環已酮清洗，待網版幹燥後再印刷
  六﹑註意事項： 1.印材和環境不同會影響印刷效果，建議試用後再大批量使用；
  2.油墨儲存及使用時，須遠離煙火，常溫保存；
  3.加入固化劑的油墨在4-6個小時用完，剩余的油墨不能倒回原罐；
  4.自然幹燥的油墨耐溶劑效果及附著力較差；
  5.烘烤時間過長或過高，白墨會發黃。
One, ink performance: bright light, good flexibility, anti - scraping and wear-resistant, alcohol resistant, solvent resistant and good attachments.
Two, applicable scope: metal, glass, ceramics, treated and untreated PP, PE, electroplating surface, UV surface and other materials.
Three, physical characteristics: 1. printing methods: silk printing, transfer.
2. over network: 80t-140t.
3. table dry time: natural drying for more than 20 minutes.
Dry time: natural drying for more than 24 hours.
Baking: the baking temperature of metal, glass and ceramics is 150 centigrade for 30 minutes.
The baking temperature of PP, PE electroplating surface and other materials is 80 centigrade for 30 minutes.
4.: 407 thinner metal open water, 783 retarder.
5. area: 35 square meters with /kg (120t screen).
6. product fineness: less than 5 mu.
7. cleaning agent: washing water, cyclohexanone.
8. scraper: 65-85 degree polyamine scraper.
Four, chemical properties: only can be mixed with this series of ink.
Five, the use of the method: 1. before the use of the ink full mixing, after use at any time closed;
2. pour out part of the ink, with the ink: the ratio of the curing agent 8:1 mixed fully, and then adding 10-30% diluent and stirring even after the printing.
3. the surface of the seal must be clean, without oil, dust and so on.
4. polychromatic printing need to be dry after the surface of the ink layer can be printed in the next color.
5. continuous printing, discontinuous printing after the use of washing net water to clean the net plate;
6. block of net plate, can wash net water, cyclohexone, wait to print after the net plate is dry, reprint
Six, attention: 1. printing materials and the environment will affect the effect of printing, it is recommended to use after a large amount of use;
2. when the ink is stored and used, it must be kept away from the fireworks and kept at normal temperature.
3. add hardener inks used in 4-6 hours, the remaining ink can not back to the original tank;
4. the solvent effect and the attachment force of the natural drying ink are poor.
[本信息来自于今日推荐网]