丝印耐酸碱电镀油墨
概述:产品特点 施工简单,高耐磨性,品质稳定,
技术参数 1、外 观:粘稠液体,20000-60000cps/25℃。
本信息已过期,发布者可在"已发商机"里点击"重发"。
产品特点 施工简单,高耐磨性,品质稳定,
技术参数 1、外 观:粘稠液体,20000-60000cps/25℃。
2、丝 网:300-400目网版,丝印刮刀:70-75度聚氨酯刮刀。
3、辅助剂:稀释剂C-2 UV专用开油水,固化剂S-8。
4、干固条件:烘烤15-30分钟,或过流水拉后直接UV固化(能量要求800mj/cm2)。
5、用 量:35-40m2/Kg。
6、储存方法:本品应储存于避光容器内,避免受热和潮湿,储存期为半年,半年后性能若无变化可继续使用。
7、包装规格:1Kg/桶
施工程序 A、UV面/真空电镀UV面/PU面
1、按照油墨:固化剂=10:1(重量比)加入S-8固化剂并搅拌均匀。
2、根据施工粘度要求加入适量稀释剂。
3、印制完成后直接过流水线。
4、UV固化(能量要求大于800-1200mj/cm2,EHT能量计)。
B、ABS/PC+ABS /PC/PMMA/HIPS等
1、根据施工粘度要求加入适量稀释剂。
2、印制完成后普通烤炉75℃烘烤15-30分钟。
3、UV固化(能量要求大于800-1200mj/cm2,EHT能量计)。
注意事项 1、使用前,应检查油墨是否与基材适应,基材表面处理程度,基材表面干净程度(是否有太多脱膜剂、离型剂、油渍),基材的柔韧性和刚性。
2、可用酒精擦拭去除灰尘、油渍、脱除脱膜剂和离型剂。
3、应试印确认后方可批量生产。
The features of the product are simple, high wear resistance and stable quality.
The technical parameters 1, appearance: viscous liquid, 2000060000cps/25 C.
2, screen: 300-400 mesh screen, silk screen scraper: 70-75 degree polyurethane scraper.
3, auxiliary agent: diluent C-2 UV special open oil, curing agent S-8.
4, dry solid conditions: baking for 15-30 minutes, or after running water to pull the direct UV curing (energy requirements 800mj/cm2).
5, dosage: 3540m2/Kg.
6, storage method: This product should be stored in the light avoidance container, avoid heat and humidity, the storage period of half a year, half a year after the performance if no change can continue to use.
7, package specification: 1Kg/ barrel
Construction procedure A, UV surface / vacuum electroplating UV surface /PU surface
1, according to the ink: the curing agent = 10:1 (weight ratio) added S-8 curing agent and stirred evenly.
2. Add appropriate diluent according to the requirement of construction viscosity.
3. After the printing is completed, the production line is directly over.
4, UV curing (energy requirement is greater than 800-1200mj/cm2, EHT energy meter).
B, ABS/PC+ABS /PC/PMMA/HIPS, etc.
1. Add appropriate diluent according to the requirement of construction viscosity.
2. Bake for 15-30 minutes at 75 C after the printing and completion of the oven.
3, UV curing (energy requirement is greater than 800-1200mj/cm2, EHT energy meter).
Precautions 1, before use, check whether the ink is compatible with the substrate, the degree of substrate surface treatment, the cleanliness of the substrate surface (whether there are too many film removal agents, release agents, oil stains), the flexibility and rigidity of the substrate.
2, using alcohol wiping to remove dust, oil stains, removal of film and deionization agent.
[本信息来自于今日推荐网]
技术参数 1、外 观:粘稠液体,20000-60000cps/25℃。
2、丝 网:300-400目网版,丝印刮刀:70-75度聚氨酯刮刀。
3、辅助剂:稀释剂C-2 UV专用开油水,固化剂S-8。
4、干固条件:烘烤15-30分钟,或过流水拉后直接UV固化(能量要求800mj/cm2)。
5、用 量:35-40m2/Kg。
6、储存方法:本品应储存于避光容器内,避免受热和潮湿,储存期为半年,半年后性能若无变化可继续使用。
7、包装规格:1Kg/桶
施工程序 A、UV面/真空电镀UV面/PU面
1、按照油墨:固化剂=10:1(重量比)加入S-8固化剂并搅拌均匀。
2、根据施工粘度要求加入适量稀释剂。
3、印制完成后直接过流水线。
4、UV固化(能量要求大于800-1200mj/cm2,EHT能量计)。
B、ABS/PC+ABS /PC/PMMA/HIPS等
1、根据施工粘度要求加入适量稀释剂。
2、印制完成后普通烤炉75℃烘烤15-30分钟。
3、UV固化(能量要求大于800-1200mj/cm2,EHT能量计)。
注意事项 1、使用前,应检查油墨是否与基材适应,基材表面处理程度,基材表面干净程度(是否有太多脱膜剂、离型剂、油渍),基材的柔韧性和刚性。
2、可用酒精擦拭去除灰尘、油渍、脱除脱膜剂和离型剂。
3、应试印确认后方可批量生产。
The technical parameters 1, appearance: viscous liquid, 2000060000cps/25 C.
2, screen: 300-400 mesh screen, silk screen scraper: 70-75 degree polyurethane scraper.
3, auxiliary agent: diluent C-2 UV special open oil, curing agent S-8.
4, dry solid conditions: baking for 15-30 minutes, or after running water to pull the direct UV curing (energy requirements 800mj/cm2).
5, dosage: 3540m2/Kg.
6, storage method: This product should be stored in the light avoidance container, avoid heat and humidity, the storage period of half a year, half a year after the performance if no change can continue to use.
7, package specification: 1Kg/ barrel
Construction procedure A, UV surface / vacuum electroplating UV surface /PU surface
1, according to the ink: the curing agent = 10:1 (weight ratio) added S-8 curing agent and stirred evenly.
2. Add appropriate diluent according to the requirement of construction viscosity.
3. After the printing is completed, the production line is directly over.
4, UV curing (energy requirement is greater than 800-1200mj/cm2, EHT energy meter).
B, ABS/PC+ABS /PC/PMMA/HIPS, etc.
1. Add appropriate diluent according to the requirement of construction viscosity.
2. Bake for 15-30 minutes at 75 C after the printing and completion of the oven.
3, UV curing (energy requirement is greater than 800-1200mj/cm2, EHT energy meter).
Precautions 1, before use, check whether the ink is compatible with the substrate, the degree of substrate surface treatment, the cleanliness of the substrate surface (whether there are too many film removal agents, release agents, oil stains), the flexibility and rigidity of the substrate.
2, using alcohol wiping to remove dust, oil stains, removal of film and deionization agent.
[本信息来自于今日推荐网]
- ks888888发布的信息
- 移印耐汽油电镀油墨
- 1、油墨特性:低气味,高光泽,遮盖力强,过网性流平性好,耐酒精,耐汽油,附着力好。 2、适用材料:主要应用于金属、五金、铝合金、不锈钢、氧化铝、标牌、金属PU、电镀件表面(含水电镀/真空电镀)、可...
- 丝印耐汽油电镀油墨
- 1、塑胶材料的外观相似,但可能会是不同的材料,客户需试印确定其符合要求后,再批量印刷; 2、在移印过程中,如出现拉丝或散开,可适当加入一些慢干膏即可; 3、环境温度过高,将会影响油墨原有质量;...
- 移印耐酸碱电镀油墨
- 生铁片 不锈钢.五金件.铝材.金属涂层. 3.适用行业: 铭板 标牌.金属包装容器 金属文具 金属玩具 刀具 交通器材 家电 产品...
- 移印耐酒精电镀油墨
- 壹﹑油墨性能: 亮光、柔韌好、抗刮耐磨、耐酒精、耐溶劑、附著力好。 二﹑適用範圍: 金屬、玻璃、陶瓷、處理過及未處理的pp、pe、電鍍面、uv面等材料。...
- 丝印耐酒精电镀油墨
- 欧莱斯MPL系列表面油墨适用对象:塑胶/金属底材罩上UV光油或油漆后,再在上面丝印油墨; 产品种类:(分RCA耐磨型/普通耐磨型)...
- 密胺餐具移印油墨 专用型密胺移印油墨
- 广泛适用于 密胺、密胺塑胶、密胺塑料、密胺餐具基材 是一种特殊用途工艺品专用墨,无毒、无味,可用水稀释,分为哑光、半光、亮光三种,清漆色泽浅,透明度高;色漆颜色鲜艳丰满。...
油墨重发信息
- 上海回收丙烯酸异辛酯公司电话
- 上海回收四氢呋喃价格公司电话
- 高蓝光油墨着色颜料3164立索尔宝红6B
- 酒泉粉末涂料颜料永固黄2G
- 英国禾大芥酸酰胺ER-CH 塑料开口剂 油墨爽滑剂
- 印刷超市DM单用纸 印刷包装用新闻纸 平板新闻纸
- 厂家生产直销紫外线灯管,紫外线高压汞灯,紫外线光固化灯管
- 山东易晟元电采暖材料 电热膜大量进行批发 安装电暖
- 西格里EK60浸渍石墨材料 树脂耐磨石墨EK60
- 深圳沙井PCB线路板激光除油墨激光开窗
- 高黑色度日本三菱 MA100 碳黑 原装进口炭黑低添加量 高效果
- 2024年越南国际涂料展览会 越南涂料展会报名入口处
- 超细吸附剂白碳黑
- 美国Taber5135耐磨试验机
- 油漆油墨类PFOA全氟辛酸检测报告欧盟限制物质检测报告